A recon Rear PTO prop shaft for series 1, 2 & 3 86, 88

Series 1, 2 & 3 Bottom PTO.
A complete restored unit. Photos are from pre restoration.
 

Rebuild belt pulley unit.
The unit was rebuild with many NOS parts like bearings, studs, nuts etc.
 

Former NOS Belt pulley unit. This unit was only fitted to a vehicle for a show once.
Please note that the drum is facing to the left side. This is ...

Rebuild belt pulley unit.
The unit was rebuild with many NOS parts like bearings, studs, nuts etc.
Please note that the drum is facing to the left ...

Front PTO for the Series Landrover. They power the Mechanical Drum Winches from Fairey.

Front pto to drive a mechanical winch like the Fairey or Mayflower.
This is one of the first units made. The lower shaft does not go through the ho...

a NOS Dowty Hydraulic pump setup.

NOS landrover center pto with selector.

One rear power take off set for long wheel base landrovers. New old stock, comes complete in the original wooden packing crate.

One rear power take off set for short wheel base landrovers. New old stock, comes complete in the original wooden packing crate.
 

Rear PTO, Center PTO including Selector and Dog clutch fully reconditionned.
Inclunding an NOS prop shaft part number 236941

Rear PTO, Center PTO including Selector and Dog clutch fully reconditionned.
Inclunding an NOS prop shaft part number 236941
The housing is optical...

This auction is for 1 out of 14 used Bottom PTOs for theLT95 and LT95A gearboxes as build in the Land Rover Perentie etc.

These were installed but...

Series Landrover One Ton Center PTO - Complete Setup

Lt95 Center PTO

Series Landrover One Ton Center PTO with selector, without dog clutch.

Series Landrover One Ton Center PTO - Complete Setup

Series 1, 2, 3 Landrover Center Power Take Off

Rear PTO, Center PTO including Selector and Dog clutch fully reconditionned.
Inclunding an NOS prop shaft part number 236941

Series Rear PTO unit, Center PTO Unit and selector. All reconditioned.
Early Series 1 Unit.

Series Rear PTO unit, Center PTO Unit and selector. All reconditioned.
Suitable for series 1, 2 & 3.

Used Center PTO for the LT95 Gearbox.
Stage One
RRC
101 Forward Control

Lt95 Center PTO

Top plate and change lever for the rear pto unit (S3, 6 cyl. Models) and for the hydraulic pto unit used on the hydraulic winch kit RTC8004 (S2a & S3)

Bottom PTO - Pivot For Upper Lever

Adaptor for Hydraulic Pump NOS. There is 1 adapter with packing, once this is sold I can provide NOS adapters with some surface rust and original p...

Coupling Sleeve for the Series Dowty Hydraulic Pump and Hydraulic Motor on the back of the MK I Winches.
Please note that only a few have the paper...

Coupling Dog for the Series Dowty Hydraulic Pump and Hydraulic Motor on the back of the MK I & MK II Winches.

Gasket for the Dowty Hydraulic Pump.

Gasket set for the Koenig L61 PTO.

This set contains both sprockets, set screws, keys and the roller chain for the Koenig PTO.

Bushing for the L621 Winches PTO. You require 2 of these.

Lower Output Shaft for the L61 PTO. The keyway has been updated so you can use regular keys. The 61L-11 will not fit.

Woodruff Key for the Koenig PTOs. You require 2 of these per unit.

Front Ball Bearing of the Koening L61 PTO.

Rear Ball Bearing of the Koening L61 PTO.

Elbow on pump for rubber connection. As well as the O ring that seals the pump.

Elbow on pump for rubber connection.

Genuine elbow pipe.

Series Hydraulic PTO - Connection for pipe, pump to control valve, on pump

Series Hydraulic PTO - Connection for pipe, pump to control valve, on pump

A new Rear PTO prop shaft for series 1, 2 & 3 86, 88

Both oil seal retainers for the rear pto unit.

Housing for the rear imput shaft bearing and housing for the output shaft front bearing.

Circlip retaining bolts for flange - rear pto unit.

Circlip, bearing to housing.
You require 4 circlips per unit.

Rear Power Take Off gasket set.

Bearing For Input/Output Shaft front/rear.
You require 4 of these bearings for 1 rear pto unit.

One remanufactured oil seal for the rear pto unit.

Replacement set bolts for the rear pto units.

4 Studs and nuts for retaining the pulley or guard to the rear PTO gear casing.

A set of shims for the spiral bevel wheel of the PTO Pulley.

A set of shims for bevel pinion bearing of the rear pto pulley. They can also be used for the rear input shaft bearing on the rear pto unit.

1 x Genuine Stud for Pulley Drive Housing on the Rear PTO Pulley (6 pieces).
As well as stud for bearing housing on the Rear PTO Unit (10 pieces).

6 nuts for the PTO Pulley unit.

Stainless replacement bolts to fix the rear pto unit to the chassies.

For sale are 5 NOS studs for end plate. You require 2 packeges for 1 pulley unit.

1 x NOS Timken Bearing for the pinion of the rear pto belt pulley.
You require 2 of these bearings per unit.

1 x NOS Timken Bearing for the rear pto belt pulley.
You require 2 of these for one unit.

Shims for Pulley Drive Pinion Housing

Shims for Bevel Wheel End Plate of the PTO Pulley.

Breather for the Belt Pulley unit.

One remanufactured filler plug for the rear pto belt pulley units.

One remanufactured oil seal for the rear pto belt pulley units.
You require 2 of these for one unit.

Gasket for the Series PTO selector housing. Center and front pto. 2.6l models

Front PTO Gasket Set for the early Fairey Mayflower PTO units.

One remanufactured sprocket for the Fairey / Mayflower power take off units. You require 2 per unit.

One new manufactured chain for the Series Front PTO.
 

Series front pto roller bearing.
You require 2 bearings per PTO.
 
(The photo shows a simmilar bearing, not the actual one)

Re manufactured front ball bearing for the series pto.

Re manufactured front ball bearing for the series pto.

Re manufactured main shaft bearing for the series landrover front pto.

3 re manufactured oil seals for the Fairey and Mayflower Power Take Off units.
This kit can be used to overhaul 1 PTO Unit.

Series PTO Shear Pin 185.
Genuine Landrover Part - New old stock.
Shears at 3356 kg.
 

Castel Nur for the Series front PTO (metric thread).

Original cover plate for the selector housing of a Fairey PTO from the 6920 Winch Kit (for Series 88 and 109 Landrover).

2 Control knobs for series landrover pto control shaft.
These will be delivered without packing, as only 1 had the packing still intact. These are ...

Genuine Series Front & Center PTO Control Knob.

Replacement Dog Clutch for the Front and Center PTO units (LT76 gearbox; will not fit 1 ton gearbox).
*these will also fit the Hydraulic PTO units.

Fork for Selector Shaft. Fits both Center and Front Pto selector Shaft.

Link Rod and operating lever as used on the MK 1 & 2 Hydraulic Winches, Fairey / Mayflower Drum Winches and variouse PTOs

Series Front and Center PTO. Circlip, fixing retaining plate.

Series Front and Center PTO. Retaining Plate for Bearing

Shaft for the later typ of selector housing.

Series PTO shaft for selector. Please note that there are several different types of these shafts, so make sure this is the correct one.

One Genuine Series PTO selector cover cork gasket.

One Series PTO Selector Cover Plate. 
(you get one of the two pictured cover plates).

Selector shaft and operating rod with nut and knob for the series 1 center ptos.
Made from stainless steel.

Flange for output shaft of the center pto. Also fits the front pto if you want to add a rear facing propshaft.

Re manufactured bearing for the Series Landrover Center PTO.
This is the rear bearing.

Re manufactured front bearing for the Series Landrover Center PTO.

Main shaft bearing for the series landrover center pto and gearbox.

Re manufactured oil seal for the Series Landrover Center PTO.
 

One Genuine Series PTO selector cover gasket.

One Series Front and Center PTO Gasket.
 

Thrust washer for bottom PTO.
As well as Land Rover Series Gearbox Intermediate Gear Thrust Washer,

Bottom Power Take Off drive shaft end cover gasket & Bottom PTO Casing to Transfer Box Shim Gaskets (set of 6).
Joint Washer for PTO housing and wa...

Bottom PTO - Stud Fixing for Pivot

Locknut for knob

Pivot Bracket for lower lever of bottom pto.

Re manufactured upper and lower lever plus clevis pins (216421 & 230279) for the bottom PTO.
 

New Shaft intermediate gear for Bottom PTO.

Ball bearing for pump drive gear shaft

Bottom PTO - Pivot For Upper Lever

Connecting link for upper and lower levers

One remanufactured spacing ring for the bottom pto of the series landrover.